Leading 10 usual forklift accidents ， forklift procedure should pay attention to these issues ！.

Do not underestimate the forklift at the workplace. If the procedure is not good, there will be major mishaps in mins, and there are lots of crashes entailing forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead might not be discovered, causing a moving crash.
Case 2: In order to maintain the balance of the forklift when lifting hefty items, the staff members utilized their body weight as the weight, which nearly created casualties.
Situation 3: The width of the forklift cargo exceeds the allowable size of the course and hangs on the roadside shelf, which almost creates an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift lifts the employees unlawfully, the forklift motorist does not wear the seat belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure must take note of these matters ：.

Beginning.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that start.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be safe before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the tons is secure and reputable.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the job site or while driving, take care that there will certainly be no obstacles in the sky. When the lots is traveling, the fork should not be elevated too high, which will impact the security of the forklift. .
3. After unloading, the fork ought to be decreased to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will certainly create the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the web traffic rules in the factory and need to maintain a specific security range from the automobile ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be effectively slanted back. The tons will not be increased except when stacking or loading. .
8. The height of the load must not block the driver's view. In unique conditions, when the product impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to stand on the fork to hold items and play a stabilizing function. .
12. If problems are found, they will certainly be repaired and reported in a timely fashion, and they will certainly never run with health problems or conceal them.

filling and dumping.
1. When fork-loading products, the distance in between the two forks need to be changed as needed to make the lots of the two forks balanced and not skewed, and one side of the item must be against the shelf. .
2. It is prohibited to work with a solitary fork or utilize a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging things, the forklift needs to be stopped with the brake. .
4. The rate of the vehicle need to be slow and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When utilizing a fork to Electric Forklift Truck for Warehouse fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch other products or things. The load must be maintained with minimal back tilt of the gantry to make sure that the load does not move in reverse. The pole can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard objects with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to select, transform pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the Stand-on Electric Pallet Stacker emergency brake deal with to dead or depress the emergency brake switch.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of vision and does not exceed 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage should additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to examine before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Running up and down the incline should be slow-moving and uniform, and no activating the slope is allowed.
7. Do not drive throughout the gradient. When the gradient is greater than 10%, the automobile ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the vehicle driver's line of sight, they must take the reversing workout
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not allowed to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Sections with a longitudinal incline higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the same length as the challenge should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844